Disable Wireless when a Wired connection is detected - BIOS setting

Disable Wireless when a Wired connection is detected - BIOS setting

This step details best practice methods for disabling the wireless radio on a wireless connection only when a wired connection is active. This is a BIOS setting, as such it is dependent on your workstation's BIOS allowing you to do this!

DELL Latitude Model E6420 and above (not available on 6410 and below!) 
a) Enter BIOS settings by pressing F2 on boot-up (On the Dell splash screen). 
b) Expand Power Management on the left and select, "Wireless Radio Control". 
c) Put a check mark in "Control WLAN Radio" and hit Enter.

Also see:

 http://agsci.psu.edu/it/how-to/enable-disable-an-enterprise-laptops-wifi

 

Enable / Disable an Enterprise Laptop's Wi-Fi

Wi-Fi, short for Wireless Fidelity, is networking technology that allows you to connect to the Internet. If you have a wireless-enabled Latitude computer you can connect to the Internet when in range of an access point called a hotspot.

When not in use your Latitude's wireless card should be disabled. By disabling Wi-Fi, you will receive two benefits:

1. Start-up times will be much faster.
   If the wireless card is ON and you are out of the office (not connected to your normal, wired connection), the laptop will try to use the Wi-Fi network during the login process to run the various start-up scripts, etc. It will eventually time-out (fail). By having the wireless card turned OFF, the start-up process will be much faster.
2. Computer will not continually search for a wireless network (and waste battery life).
   If you are in the office (connected to your normal, wired connection) or in a location where there is no wireless hotspot, you don't need to have the computer waste processing power by looking and looking for a wireless hotspot. By disabling Wi-Fi, you will gain a little more power for your other tasks. In addition, you will maximize your battery operating time by disabling wireless activity.
   
   NOTE: After your Latitude has started up completely, you can ENABLE the wireless card and connect to a wireless hotspot. For example, a wireless router at your home or at a local coffee shop. If you have connected to this hotspot previously, the wireless card should connect automatically for you.
   
   NOTE: Once you have the wireless card enabled, before you shut down the computer, you should again DISABLE the card. The computer will then be ready for the next time you turn it on with wireless turned off.
   

Enable / Disable with Hardware Switch

The more recent Latitude models have a wireless switch to enable or disable wireless network devices and the
Wi-Fi Catcher Network Locator.
Dell Latitude E6420 and E6520 Series
These laptops have a small switch on the RIGHT side of the keyboard. The switch is toward the front of the laptop. The Wi-Fi Catcher™ icon will is above  the keyboard. You will see a lit radio tower if the wireless switch is enabled.




Dell Latitude E-Series
These laptops have a small switch on the RIGHT side of the keyboard. The switch is toward the back of the laptop. The Wi-Fi Catcher™ icon will be on the switch.
"off" position - Disables wireless device
In an improvement over the earlier models, when the switch is in the "off" position, you see an orange panel next to the switch.
 
"on" position - Enables wireless device


Dell Latitude D820 or D830These laptops have a small switch on the LEFT side of the keyboard.

1 - "off" position - Disables wireless device
2 - 'on" position - Enables wireless device
3 - "momentary" position - Scans for Wi-Fi networks
4- Wi-Fi Catcher™ light

• Flashing green: Searching for networks
• Solid green: Strong network found
• Solid yellow: Weak network found
• Flashing yellow: Error
• Off: No signal found

Enable / Disable with Software (via Control Panel)

Older models without the switch, or newer models as well, can turn off (disable) or turn on (enable) the wireless card via the Windows Control Panel. These steps will focus on disabling the wireless card. See the "NOTE" for enabling the card again.
Windows XP

1. Click Start and choose Control Panel. Double click on Network Connections icon.
2. Look for the Wireless Network Connection icon. When you see it, Right Click on the Wireless Network Connection icon.
3. If you see an Enable choice, the Wi-Fi is already disabled. You're good to go. Close the Network Connections window.
   
   If you see a Disable choice, select it. This will disable the wireless card. Close the Network Connections window.
   
   NOTE: When you need access to the wireless card, you can repeat Steps 1 and 2 to view the Wireless Network Connection icon. Enable the card by Right Clicking and choosing Enable.
   

Windows 7

1. Click Start and choose Control Panel. Click the Network and Sharing Center icon.
2. On the left side, click the Change adapter settings link.
3. Right Click on the Wireless Network Connection icon.
4. If you see an Enable choice, the Wi-Fi is already disabled. You're good to go. Close the Network Connections window.
   
   If you see a Disable choice, select it. This will disable the wireless card. Close the Network Connections window.
   
   NOTE: When you need access to the wireless card, you can repeat Steps 1 and 2 to view the Wireless Network Connection icon. Enable the card by Right Clicking and choosing Enable.

No network provider accepted the given network path.

 

I was getting the following error connecting to somlh17 and somlh35 shares.  "No network provider accepted the given network path."   I could connect to the internet and sommail, and I can ping somlh17 and somlh35.  Shutting down and rebooting fixed this issue previously but was not able to this time.  The following fix from MS worked for me.

http://support.microsoft.com/kb/841570

While you are using a computer that has one of the operating systems that are listed in the "Applies To" section installed, you may experience either of the following symptoms.

• When you try to connect to a network share, you may receive the following error message:

No network provider accepted the given network path.

• You may also receive the following error message:

Workstation service terminated with service-specific error 2250

CAUSE

This issue occurs because the Mup.sys file is missing or corrupted.

RESOLUTION

To resolve this problem, follow these steps:

1.     Restart your computer in Safe mode.

2.     Use System File Checker with the /scannow parameter to immediately scan and verify the versions of all the system files that Windows File Protection helps protect. You must be logged on as an administrator or as a member of the Administrators group to run System File Checker. You can run the sfc /scannow command to use System File Checker.

3.     If you get information about the corrupted Mup.sys file, expand the Mup.sys file from the Windows XP CD to the C:\Windows\System32\Drivers folder. For example, if the CD drive is D, type the following at a command prompt:

expand d:\i386\mup.sy_ c:\windows\system32\drivers

4.     Expand the Mup.sys file from the Windows XP CD to the C:\Windows\System32\Dllcache folder. For example, if the CD drive is D, type the following at a command prompt:

expand d:\i386\mup.sy_ c:\windows\system32\dllcache

Note You can also use Expand File in the System Configuration Utility (MSCONFIG). 

For more information, click the following article number to view the article in the Microsoft Knowledge Base:

310560  How to troubleshoot configuration errors by using the System Configuration utility in Windows XP

This fix didn't work this time around. running out of time I reinstalled the NIC drivers from Dell and updated the BIOS from A10 to A15 I think. Reboot after that brought this back.

Posted 08:03, 2 Oct 2009